Common steps for proper use of MSR and PEAK-1:
The use of MSR steps:
Inject oil to the oil bottle full of oil line, about 7-8 minutes full; screw the seal to the oil bottle, but not too tight, first inflate 3-7, check the movement Pu no oil; open Furnace tripod and connect the seal with the oil bottle, remember to install the flame reflection sheet; again check all O-Ring at the leak, unscrew the oil valve to drain the oil to the preheat plate, about 1/1 2, then close (Note: There can be no overflow, if there is an overflow, you can not ignite for the time being, please go to it, or go out of the overflowing oil to volatile oil, re-ignite); Ignition preheating; After the flames in the plate are extinguished, they will be ignited above the stove. If the pressure in the oil bottle is too low, pump 10-20 times, depending on the situation. Place the pot and enclose the windshield.
Steps for using PEAR-1:
1. Open the stand of the stove and place it on the floor;
2. Add about eight full oils first;
3. Lock the oil cap;
4. Unscrew the seal, press the air intake, and inflate about 25 times.
5. Open the oil valve and ignite;
6. Put on the pot and wind the windshield to use it.
Troubleshooting:
When it comes to troubleshooting, the first thing to understand is the construction of the stove. The following are MSR and PEAK-1:
MSR: MSR is now referred to as the "Intemational Whisperlite 600UA" is not XGK-2. Most of the former are used, so the emphasis is on the former.
The most common faults can be explored from two major parts: one is Feng Pu; the other is the stove itself.
Let us discuss one by one:
1. The problems encountered by Feng Pu himself: Feng Pu encountered an upset
For example, when the fuel bottle is pumped without pressure, the cause may be the wear of the cup and it must be updated.
2. Another case is that the leather cup is not sufficiently lubricated.
For example, if the problem persists, the final processing method would have to remove all the sealed Pu line pieces, and clean them all with clean oil until they are clean and then assemble them back; however, remember the order of parts. Do not leave out when assembling.
3. Another more serious problem is Fengpu’s oil leakage. There are four places where oil leakage can occur in Fengpu:
A oil bottle and sealing seam O-Ring;
O-Ring outside the convergence between B and Pu.
C-valve and seal along the chain -Ring;
D. Incorporating the intake valve (ball) fault in the pump, where the first three faults are replaced with rubber gaskets, the problem can be eliminated immediately. The fourth problem is the need to replace the iron and fluorine balls and springs; however, the fault The rate is not too great.
Furnace problems:
The common failure of the furnace is that the tubing is not fluent or the nozzles are blocked. The method of processing is the oil pipeline or the nozzle. It can be discussed from two aspects: one is the internal blockage of the tubing, and the other is the nozzle blockage.
The first type of fault handling:
If the obstruction of the oil pipe is not serious, the oil line may be drawn back and forth so that the carbon deposit of the oil line will fall off automatically due to friction with the inner wall of the oil pipe;
If you can't solve the problem, you have to pull out the oil line and insert it with clean paper or cloth.
If the carbon deposition is still serious, when the assembly is back, the firepower is still not strong; you have to use the final method to extract the oil line and use a small fire (preferably using a gas stove) to burn the carbon on the oil line when you When it is loaded back, first use the cassette gas stove to align with the inner wall of the oil pipe to accelerate the smooth carbon deposition on the inner wall of the oil pipe. Finally, put the oil line back and you're done.
If the problem still cannot be ruled out, it is necessary to replace the new tubing or send the company to repair. The carbon deposit of the nozzle can be cleared by the use of a pin, and the new type of stove is now equipped with an automatic pin, so long as it is shaken up and down, it can be removed.
In addition, there are still many glitches, such as small flames, red fire on the flames, etc. The order of repairs is still examined according to the above method.
If the firepower is too small, the possible cause is partial blockage of the oil, which can be solved by clearing the manifold or nozzle. If not, there may be no oil in the oil bottle, or the pressure in the oil bottle is not enough or even leaks. The treatment method is:
A fuel tank to eight minutes full;
B pressurization
C check all O-Ring;
D Ignition, be sure to note that when the oil leaks, it cannot be ignited. Otherwise, it will cause a fire.
In order to take advantage of the fire-fighting method, to adjust the sub-flame disk or replace the nozzle, it is also possible to add the wrong fuel factor, or the oil-gas mixture ratio is not correct, and the method of treatment can be overhauled or sent to the company for maintenance. If there is oil leakage at the seam of the tubing, the tubing needs to be replaced. There is no other way.
PEAK-1: stoves produced by American companies, the company's production of stoves, functions and methods of use are similar, except for the APEX-2 one, is more special, other models of the structure is roughly similar; now with PEAK -1 400 for maintenance discussion, PEAK-1R failure, roughly divided into two major parts, internal and external:
internal:
Inflated and sealed, there are the following possible causes of the fault:
A, inflated leather bowl wear, or is not enough lubrication, processing methods to update the bowl or add lubricants, the problem can be solved;
B. The plastic cover of the solid-filled seal is melted down. The method of treatment needs to replace the new crock.
C. The leakage of oil in Fengpu must be sent to the company for repair. Pipeline obstruction, treatment method to extract the oil line in the tubing (Note: Be careful, so as not to break), and then use a fine sandpaper to rub the carbon clean, and then assembled back; if the obstruction is too serious, had no choice but to change the root.
When you ignite the stove, when you ignite, there is only sound of gas, no volatile oil and gas, and the stove cannot be ignited due to the use of the right. This is due to the unequal ratio of oil and gas pressure inside the furnace, resulting in air in the tubing, no fuel, and treatment methods. Unscrew the oil valve from the stove and replace the oil suction tube that is screwed under the oil valve. (This kind of failure is less likely unless you are sure of the correct dismantling. If not, please hand it over to the company.)
Oil valve failure, send factory maintenance.
external:
1. The foot of the stove is broken and replaced;
2, the cover leak, replace the rubber pad inside.
3. Special Situations: The special circumstances mentioned here are the most serious ones. How to deal with them? The most important thing is not to panic, first look at the side with or without tools to help you extinguish the fire, but remember that you can not use it, do not put out, it is best covered with a damp cloth, if it is PEAK-1 fire, with its own aluminum cylinder or iron cylinder Cover it, if it is MSR cover it with a cloth, do not throw it on the floor, this will only cause longer burning, or even the risk of explosion.
4, the repair kit production: Why do repair kits, is to facilitate you, when the stove is not normal, emergency repair tools.
MSR repair kit, including: 1, wrenches; 2, O-ring (three types); 3, leather cups; 4, needles;
PEAK-1 repair kits include: 1, wrenches; 2, sandpaper; 3, lubricants; 4, cups.
Perforated Standard Gn Pan,Perforated Gastronorm Pans,Perforated Gastronorm Trays,Stainless Steel Food Pans
Jiangmen Junerte Stainless Steel Kitchenware Co.,Ltd , https://www.jetkitchenware.com