How to extend the service life of PVC flooring

PVC flooring has become a popular new building material on the market. However, improper construction may have a great influence on the overall effect during the laying process. To avoid the following problems, several PVC flooring problems will definitely help you The service life of the PVC floor.

1. When laying PVC flooring, any expansion gap is less than 1cm, especially when the door edge and corners and concealed parts are paved, rough estimate of the expansion gap or saw blade, so that any contact with the fixed floor. As long as any contact with the fixture on the floor will occur force and reaction force, partial or full arch, severe joint cracking or warping.

2. The concrete floor has been completed for less than three months, or it has been completed for three months. However, the doors and windows of the room are closed, and there is no ventilation, no ventilation, and the humidity is too large. In this case, the PVC floor will be arched for a little longer time. Cracking or cracking of joints or joints.

3. Before the PVC floor, although the geothermal heating room had already been tested for heating, the geothermal construction unit did not raise the temperature to the earliest, or did not continuously observe changes in the ground temperature, and stopped the experiment after the local area had a temperature. In this way, a large amount of moisture and warm air have not been emitted. After the local board is paved, once the heat is supplied again, the surge of moisture and moisture that could not be emitted increases rapidly. Or even if a full experiment is done, the geothermal temperature is not gradually increased after pavement, but raised once in place, so that too quickly and quickly rise to the limit temperature of moisture, moisture, heat, resulting in the floor arching or cracking Bubbling phenomenon.

4, PVC floor pavement for several months without staying in the room for a long time, doors and windows closed, so that the indoor air does not flow, humidity is not enough. Especially in the winter and summer seasons, the "stuffed board" in this environment is prone to arching and cracking.

5, the user did not press the paving instructions and "warranty card" to maintain the floor, especially when cleaning the floor, so that the patchwork joints into the water or joints often wet, resulting in joint cracking and corner tilt.

6, PVC floor pavement paving workers in order to catch up with schedule to grab time, or simply rely on experience is not careful according to the "Paving Instructions" operation, the following phenomenon of illegal paving: 1. The size of the first stitching is beat paving; 2 The pad was too hard or improperly positioned when the pad was struck, and there was no evidence of damage to the lock; 3. Excessive force was applied when tapping, making the seam too tight and slightly arching; 4. Repeatedly repeated beats to destroy The lock seam; 5. Beating powerless, did not fasten patchwork.

7, PVC floor pavement, the individual floor locks are not standardized (too loose) or tight, the lock has been destroyed, did not pick out, but good or bad mixed, resulting in problems.

8, winter paving, due to increased floor water absorption, and PVC flooring "hibernation" reasons, did not put the floor before the user's room for more than 12 hours to adapt to the temperature and "frozen recovery", so the floor after laying a period of time, produce problem. When paving, the floor mats are not staggered and overlapped. In particular, the floor mat joints are not completely sealed with self-adhesive tape, so that the moisture is pulled out from one place. In this case, the joint is not cracked, that is, bubbling or warping. . This is the most common and most common cause.

specific methods:

1, sand protection: should be in the use of PVC plastic floor prices at the entrance, the entrance hall to place a protective sand and gravel, to prevent the shoes will be brought into the room sand to the floor surface scratch;

2. Handling of articles: When carrying articles, especially when there are sharp metal objects at the bottom, do not drag on the floor to prevent the floor from being injured.

3, pyrotechnic protection: Although the PVC plastic floor is a fire rated for flame retardant grade (B1) floor, does not mean that the floor will not be burned by fireworks, so when people use PVC flooring, do not burn the cigarette, mosquito coils, charged The iron and high-temperature metal objects are placed directly on the floor to prevent damage to the floor;

4, regular floor maintenance: PVC plastic floor cleaning using neutral detergent cleaning, can not use strong acid or alkali cleaner to clean the ground, do a good job of regular cleaning and maintenance work;

5, pollution treatment: PVC plastic floor stained ink, food, oily, etc. should wipe away the dirt, and then wipe the traces with a diluted detergent, the residue of the black leather shoes India is difficult to remove the veil can be used to touch the pine scrub, not The pine perfume is poured on the floor for cleaning, after the scrub, it should be repaired with wax;

6, Note: Floor cleaning can not use clean ball, knife scraping, can not use conventional methods to clean the dirt, consult relevant parties, can not mess with the use of acetone, toluene, and other chemicals;

7, chemical protection: to avoid a large amount of water stay on the floor surface for a long time, especially the block floor, homogenous floor, water soaked the floor for a long time, may seep into the floor below the floor glue to lose the adhesive force, it may also Makes the floor surface of the protective wax moisture layer cause floor pollution, and may also cause sewage to penetrate into the floor to cause floor discoloration (homogeneous floor);

8, sun protection: Avoid direct exposure to bright light, make the floor to put ultraviolet radiation, to prevent the floor discoloration, fading.

Note: Dust and sand on the floor of pvc floor will damage the floor material. If there is any dip substance, surface discoloration may occur. Please remove these substances at any time and clean them regularly. When the partial impregnation is serious, use a neutral detergent to clean it, then use a wet rag to scrub, and it is strictly forbidden to use steel balls and wire brushes to clean the dirt so as not to damage the surface of the floor. When washing with a lot of water, care should be taken to prevent moisture from escaping from the connecting part or the striated part, causing the product to stick and the connection part to open. Solvents, furniture lacquers, radioactive liquids, medicines and other products need to be immediately removed with alcohol when they fall to the ground. Note: When using a strong solvent such as acid or acetone, the dyeing area may be enlarged, softened, and discolored.

Plastic Basketball Court http://
Plastic venue http://
Plastic tennis court http://

Compostable means that a product is capable of breaking down into natural elements in a compost environment. Because it`s broken down into its natural elements it causes no harm to the environment. The breakdown process usually takes about 90 days. The ASTM defines compostables as anything that undergoes degradation by biological processes during composting to yield CO2, water, inorganic compounds and biomass at a rate consistent with other compostable materials and leaves no visible, distinguishable or toxic residue.

compostable  bags

Disposable Compostable Plastic Bags

Compostable Bags,biodegradable plastic bags,compostable trash bags,biodegradable bags

Ningbo ECO Biodegradable Technology Co., Ltd , https://www.chinabiodegradable.com